Visit site
  • Brianna Linkert

    Twine Lanterns (translated) Materials Needed 1. The usual round balloon of any size, but not less than 40 cm 2. Knitting yarn (3-4 coils) 3. Glue on the basis of starch (2-3 bottles) 4. PVA glue (can be replaced starch-based adhesive, but properties of PVA is worse) 5. Wire and lighting fixtures for pendant lamp (you can buy in "1000 detail" or other hardware stores) 6. Bulb 7. Ceiling Hook 8. Scissors 9. Waterproof fabrics, oil cloth or a piece of tarpaulin 10. Rubber gloves 11. Foam Brush 12. Brushes or plastic cover Step 1 The first thing to do is inflate the balloon to its maximum size and tie it so it does not deflate. Try to inflate the balloon so that it has a round shape - because the shape of a ball overhaul will affect the final shape of the lampshade. You can use the ball of any size, but start with a diameter of 40 cm, to go through all the steps of instruction and learning by experience not to make light less than the size of the balloon. Step 2 Now try to remember how to do a mask or a globe out of papier-mache in elementary school, using a balloon as a basis on which the superimposed layers of paper. We will do roughly the same thing, only instead of papier-mache will use knitting yarn, soaked in glue or PVC glue solution on the starch. These actions will create the basis for the light. Step 3 Take the end of the thread and tie it at the bottom of the balloon to the side where the ball is inflated and fixed. This will be the top of the lampshade, and we cut out this site later, so do not worry about the protruding ends or the size of the site. Step 4 Pick up a ball of yarn and start winding the balloon thread. Design lampshade is entirely dependent on the method and sequence in which you wrap the ball of thread. It is important to try to distribute the yarn evenly to a thickness of the tube across the surface of the same. For the first time do not try to do something unusual or unique, better focus on the uniform application of the cross-taut strings. Everything you need to achieve, so it is fairly tight tension, while at the same time not distorting the shape of the balloon. Step 5 Continue to wind the thread around the ball until you are sure that we were able to do 5.4 flat layers over the entire surface. The result should be wound enough yarn to completely hide the balloon. If you see small gaps that remain, do not worry - these gaps allow light to break through in some places more clearly and make the final design unique. Step 6 Cut the thread and tie a knot on the balloon. Step 7 Cover the work surface waterproof cloth tablecloth dining room or a piece of canvas and begin to spray onto the surface of the ball resulting PVA glue or starch-based adhesive. Step 8 Wear rubber gloves and using foam brush apply a large amount of adhesive on the entire surface of the lamp of the future. You need to saturate every thread of glue around the ball, because if even one of them will remain dry, the shade will not form an ideal, and in the worst-case scenario - just fall apart. Step 9 Leave the ball in the wires to dry overnight. If possible, it is better to hang, then the resulting surface foundations will not come into contact with anything that could distort the shape of the perfect shade. Step 10 Once the foundation is dry, with the help of needles, pins, or need to pop the knife inside the balloon. Maybe in some places, the remnants of the ball would have to scrape the inner wall of the resulting shade. Step 11 Cut a small hole at the top of the ball around the site, which tied the ends of the filament. The hole should be sized so that you can slide the bulb through it, but no more. Step 12 Insert the lamp shade light fixtures and replace the bulb. To fix the valves inside the lamp, wrap the wire around a few thin brushes, then thread the inside of the sphere and flatten. Adjust the length of the wire to position the element of light in the center inside the lampshade. Step 13 Attach the new fixture to the ceiling hook and turn on the light. All done!

  • Sarai N Rivera

    DIY light fixture Using Balloons

  • Tina ❤️

    Craft idea to make a lamp shade out of a balloon and string

  • Kathryn Elton

    DIY Ball Light Fixtures. use a punch ball balloon from the $ store

Related Pins

Make your own lava lamp sounds like a fun activity mixed with articulation cards for a middle-elementary aged child.

Seriously clever! A headlamp around a gallon of water = ambient light for your tent and a great night lamp when the power is out.

so cute! paper cup lights!

this diy lamp is too funny #pin_it @mundodascascas See more Here: www.mundodascasas...

diy Awesome Desk Lamp Hmmm endless possibilities with this idea. You could paint the blocks or even add things between the gaps.

This would be awesome to do with my dad's old slides!

DIY Twine Holders! Candlestick bottoms, wooden dowel, knob topper and 2 magnets. Think it work well with sewing tread too.

#1- Great idea! #2-Hmm. Someone did a REALLY nice job on these. For me, the screw top needs to be hidden, My ocd says NO NO! Could do beaded trim, embroidered ribbon, embossed metal strip, strand of pearls wrapped round & round, etc. Beautiful!

strings in jar; I have an unnatural obsession with color + white baker's twine NOW I KNOW WHAT TO DO WITH MY EMPTY PICKLE JAR!!! LOVE THIS!!!

Make a glitter discoball from a paper lantern. There are heaps of ways to use glitter on this site, this one is just one of my faves.